| Electrical | |
|---|---|
| General | |
| Compliant Specification | Meets AS/NZS 4365 for radio communications equipment in the UHF citizen and personal radio service. |
| Frequency Range TX | 476.425-477.4125 MHz |
| Number of Channels | 80 |
| Channel Spacing | 12.5 kHz |
| Operation Mode | Simplex or half Duplex with repeater talk around. |
| Scanning Speed | 50 ms per channel (20 channels per second). |
| Antenna Impedance | 50 Ohms nominal |
| Nominal Battery Voltage | 12 volts DC |
| Operating Voltage Range | 10-16 volts DC |
| Battery Polarity | Negative Earth |
| Standard Test Voltage | 13.8 volts DC |
| Overvoltage Protection | 30 volts DC maximum. At 18 volts DC the channel display flashes 'Hi DC' for 5 seconds on receive. The RF power is reduced and TX flashes on transmit. |
| Reverse Voltage Protection | Diode Crowbar |
| Overcurrent Protection | In-line 2 amp fuse |
| Operating Temperature | -10C to 60C |
| Transmitter | |
| RF Output | 5 watts |
| Spurious Emission | < - 70 dBc |
| Frequency Error | < 1.5 kHz |
| Modulation | FM |
| Maximum Deviation | < 2.5 kHz at + 20 dB AF limiting. |
| Transmit Frequency Response | + 6 dB per octave 300 Hz to 3 kHz + 1-3 dB. |
| Demodulated Audio Signal to Noise | > 45 dB unweighted |
| Current Consumption | 1.7 amps with 50 Ohms termination. |
| Receiver | |
| Intermediate Frequencies | 38.85 MHz |
| Sensitivity | - 122 dBm for 12 dB SINAD unweighted |
| Selectivity | - 6 dB at + 3.5 kHz ' 60 dB at 12.5 kHz |
| Intermodulation Immunity | -72 dB |
| Blocking Immunity | -98 dB |
| Spurious Response Immunity | 70 dB |
| Audio Output Power | 3 watts average into 4 Ohms |
| Audio Signal to Noise | > 45 dB unweighted |
| Receive Frequency Response | ' 6 dB/Octave de'emphasis 300 Hz to 3 kHz + 1-3 dB. |
| Current Consumption | < 175 mA muted 750 mA Full volume. |
| Conducted Spurious Emission | < - 70 dBm |
| Mechanical Specifications & Connections | |
| Dimensions: | 29 (H) x 128 (L) x 117 (D) mm |
| Weight | 450 grams |
| 12 Volt Power Supply | Two core cable with bulkhead connector in rear panel. |
| Antenna | SO239 Panel Socket |
| External Speaker: | 3.5 mm Mono Jack |
| Microphone Port | 6 Way telephone style with rubber strain relief. |
GME TX3520S
Specifications
| Electrical | |
|---|---|
| General | |
| Compliant Specification | Meets AS/NZS 4365 for radio communications equipment in the UHF citizen and personal radio service. |
| Frequency Range TX | 476.425-477.4125 MHz |
| Number of Channels | 80 |
| Channel Spacing | 12.5 kHz |
| Operation Mode | Simplex or half Duplex with repeater talk around. |
| Scanning Speed | 50 ms per channel (20 channels per second). |
| Antenna Impedance | 50 Ohms nominal |
| Nominal Battery Voltage | 12 V DC |
| Operating Voltage Range | 10-16 V DC |
| Battery Polarity | Negative Earth |
| Standard Test Voltage | 13.8 V DC |
| Overvoltage Protection | 30 V DC maximum. At 18 volts DC the channel display flashes 'Hi DC' for 5 seconds on receive. The RF power is reduced and TX flashes on transmit. |
| Reverse Voltage Protection | Diode Crowbar |
| Overcurrent Protection | In-line 2 amp fuse |
| Operating Temperature | -10C to 60C |
| Transmitter | |
| RF Output | 5 watts |
| Spurious Emission | < - 70 dBc |
| Frequency Error | < 1.5 kHz |
| Modulation | FM |
| Maximum Deviation | < 2.5 kHz at + 20 dB AF limiting. |
| Transmit Frequency Response | + 6 dB per octave 300 Hz to 3 kHz + 1-3 dB. |
| Demodulated Audio Signal to Noise | > 45 dB unweighted |
| Current Consumption | 1.7 amps with 50 Ohms termination. |
| Receiver | |
| Intermediate Frequencies | 38.85 MHz |
| Sensitivity | - 122 dBm for 12 dB SINAD unweighted |
| Selectivity | - 6 dB at + 3.5 kHz ' 60 dB at 12.5 kHz |
| Intermodulation Immunity | -72 dB |
| Blocking Immunity | -98 dB |
| Spurious Response Immunity | 70 dB |
| Audio Output Power | 3 watts average into 4 Ohms |
| Audio Signal to Noise | > 45 dB unweighted |
| Receive Frequency Response | ' 6 dB/Octave de'emphasis 300 Hz to 3 kHz + 1-3 dB. |
| Current Consumption | < 175 mA muted 750 mA Full volume. |
| Conducted Spurious Emission | < - 70 dBm |
| Mechanical Specifications & Connections | |
| Dimensions | 29 (H) x 128 (L) x 117 (D) mm |
| Weight | 450 grams |
| 12 Volt Power Supply | Two core cable with bulkhead connector in rear panel. |
| Antenna | SO239 Panel Socket |
| External Speaker | 3.5 mm Mono Jack |
| Microphone Port | 6 Way telephone style with rubber strain relief. |
Vertex VX820 Series Handhelds
General Specification
Frequency Range 134 - 174MHz 400 - 470MHz; 450 - 520MHz
Number of Channels 512 and 32 Groups (VX-829/VX-824)
and Groups 16 and 1 Group (VX-821)
Power Supply Voltage 7.4 V DC 20%
Channel Spacing 12.5 / 20 / 25kHz
PLL Steps 5 / 6.25kHz
Battery Life (5-5-90 duty)
3000 mAh FNB-92LI 23 hours (18hrs w/o saver) 21.5 hours (16.5hrs w/o saver)
2000 mAh FNB-V87LI 16 hours (12.5hrs w/o saver) 15 hours (11.5hrs w/o saver)
IP Rating IP 57
Operating Temperature Range -30C to +60C
Frequency Stability 2.5ppm
RF Input-Output Impedance 50 Ohms
Dimension (H x W x D) 96.5mm x 57.5mm x 37.5mm (w/FNB-86LI)
Weight (Approx.) 310g (w/FNB-V86LI and Belt Clip)
Receiver Specification: measured by TIA/EIA-603
Sensitivity 12dB SINAD 0.25 / 0.32V
Adjacent Channel Selectivity 75 / 70dB
Intermodulation 75 / 70dB
Spurious and Image Rejection 75dB
Hum and Noise 48 / 42dB
Audio Output 700 mW @ 16 Ohms 5% THD
Transmitter Specification: measured by TIA/EIA-603
Output Power 5 / 2.5 / 1 / 0.25W
Modulation 16K0F3E, 11K0F3E
Spurious Emissions 70dB below carrier
FM Hum & Noise 45 / 40dB
Audio Distortion < 3 % @1kHz
GME TX3500
| Electrical | |
|---|---|
| General | |
| Compliant Specification | Meets AS/NZS 4365 for radio communications equipment in the UHF citizen and personal radio service. |
| Frequency Range TX | 476.425-477.4125 MHz |
| Number of Channels | 80 |
| Channel Spacing | 12.5 kHz |
| Operation Mode | Simplex or half Duplex with repeater talk around. |
| Scanning Speed | 50 ms per channel (20 channels per second). |
| Antenna Impedance | 50 Ohms nominal |
| Nominal Battery Voltage | 12 volts DC |
| Operating Voltage Range | 10-16 volts DC |
| Battery Polarity | Negative Earth |
| Standard Test Voltage | 13.8 volts DC |
| Overvoltage Protection | 30 volts DC maximum. At 18 volts DC the channel display flashes 'Hi DC' for 5 seconds on receive. The RF power is reduced and TX flashes on transmit. |
| Reverse Voltage Protection | Diode Crowbar |
| Overcurrent Protection | In-line 2 amp fuse |
| Operating Temperature | -10C to 60C |
| Transmitter | |
| RF Output | 5 watts |
| Spurious Emission | < - 70 dBc |
| Frequency Error | < 1.5 kHz |
| Modulation | FM |
| Maximum Deviation | < 2.5 kHz at + 20 dB AF limiting. |
| Transmit Frequency Response | + 6 dB per octave 300 Hz to 3 kHz + 1-3 dB. |
| Demodulated Audio Signal to Noise | > 45 dB unweighted |
| Current Consumption | 1.7 amps with 50 Ohms termination. |
| Receiver | |
| Intermediate Frequencies | 38.85 MHz |
| Sensitivity | - 122 dBm for 12 dB SINAD unweighted |
| Selectivity | - 6 dB at + 3.5 kHz ' 60 dB at 12.5 kHz |
| Intermodulation Immunity | -72 dB |
| Blocking Immunity | -98 dB |
| Spurious Response Immunity | 70 dB |
| Audio Output Power | 3 watts average into 4 Ohms |
| Audio Signal to Noise | > 45 dB unweighted |
| Receive Frequency Response | ' 6 dB/Octave de'emphasis 300 Hz to 3 kHz + 1-3 dB. |
| Current Consumption | < 175 mA muted 750 mA Full volume. |
| Conducted Spurious Emission | < - 70 dBm |
| Mechanical Specifications & Connections | |
| Dimensions: | 29 (H) x 128 (L) x 117 (D) mm |
| Weight | 450 grams |
| 12 Volt Power Supply | Two core cable with bulkhead connector in rear panel. |
| Antenna | SO239 Panel Socket |
| External Speaker: | 3.5 mm Mono Jack |
| Microphone Port | 6 Way telephone style with rubber strain relief. |
GME TX3600
GENERAL
Compliance: Compliant with AS4295
Frequency Bands: UHF- 450 to 520 MHz
Number of Channels: 99 + 40 UHF CB
Channel Spacing: 25 kHz, 12.5 kHz (narrowband)
Channel Step: 6.25 kHz
Frequency Stability: +/- 1 kHz
Modulation: FM
Operation Mode: Simplex, Half Duplex
Scan Speed: 50 ms/100 ms/200 ms
Antenna Impedance: 50 Ohms
Antenna Connector: BNC
Nominal Voltage: 12V DC Negative Earth
Operating Voltage: 10.8 V to 15.6 V
Test Voltage: 13.8 V DC
Reverse Polarity: Diode Crowbar
Over Voltage Protection: 18 V Crowbar
Current: RX muted 0.2A TX 5 Watts 2.5A (UHF)
TRANSMITTER
RF Output: H: 5W L: 1W (adj.)
TX Duty Cycle: 1:4 for 5W Output
RF Switching BW: UHF - 70 MHz
Deviation Limiting: 5 kHz / 2.5 kHz @ + 20 dB
Pre-Emphasis: +6 dB/oct + 1/-3 dB 300 Hz to 3 kHz
AF Distortion: 3% Below Limiting
Residual Modulation: -45 dB
Spurious Outputs: <-75 dBc
RECEIVER
Circuit: Double Conversion
Intermediate Frequencies: UHF 45MHz, 455 kHz
Sensitivity (12 dB SINAD): -122 dBm
Adjacent Channel Selectivity: 73 dB, 65 dB (narrowband)
Intermodulation Rejection: 74 dB
Blocking: > 100 dB
Spurious Rejection: > 75 dB
RF Switching Bandwidth: UHF - 70 MHz
Audio Power 3W into 4 Ohms
MECHANICAL
Dimensions: 29 (H) x 127 (L) x 163 (D) mm
Weight 620 grams
Specifications are subject to change without notice. They are issued as a guide only and shall not
form part of any contract without the express written authorisation of GME.
TX3820V
| ||
| Compliant Specification | Compliant with Australian Test Standard AS4295 | |
| Frequency Bands | 136 - 174 MHz | |
| Number of Channels | 99 | |
| Channel Spacing | 25 kHz / 12.5 kHz (N) Version | |
| Frequency Stability | +/- 1khz VHF (-10 to +60) | |
| Modulation | Direct FM | |
| Operation Mode | Simplex or half duplex with repeater talk-around | |
| Scanning Speed | Selectable 50/100/200 ms per channel | |
| Antenna Impedance | 50 Ohms nominal | |
| Antenna Connector | BNC (chassis mount) | |
| Nominal Voltage | 13.8 volts DC negative earth | |
| Operating Voltage Range | 10.8 - 15.6 volts | |
| Test Voltage | 13.8 volts DC | |
| Reverse Polarity Protection | 18 volt diode crowbar | |
| D.C. Current | 0.2 amps receive (power save < 60 mAh) | 6 amps (UHF) transmit into 50 Ohms | |
| TRANSMITTER | ||
|---|---|---|
| Operating Temperature Range | -10 C to +60 C | |
| RF Output | High: 25 watts max | Low: 5 watts adjustable | |
| Transmit Duty Cycle | 25% at maximum output (25 watts) | |
| RF Switching Bandwidth | VHF 38 MHz | |
| Deviation Limiting | 2.5 kHz or 5 kHz at +20 dB AF limiting | |
| Pre-Emphasis | +6 dB per Octave | |
| AF Distortion | 3% below limiting | |
| Residual Modulation | -40 or -45 dB | |
| RECEIVER | ||
| Sensitivity Spurious Outputs | -122 dB for 12 dB SINAD (CCIR) < -75 dBc (Compared to carrier) | |
| Circuit Type | Double conversion superheterodyne | |
| RF Switching Bandwidth | VHF-38 MHz | |
| Intermediate Frequencies | 1st: 21.4 / 38.85 MHz | 2nd: 450 kHz | |
| Sensitivity | -121 dBm for 12 dB SINAD unweighted | |
| IF Frequencies | 45mhz | |
| Adjacent Channel Selectivity | -73 dB/-65db (WB/NB) | |
| Intermodulation | 74 dB | |
| Blocking | > 100 dB | |
| Spurious Rejection | > 75 dB | |
| Audio Power | 3 watts average into 4 Ohms | |
| Audio Signal to Noise | > 45 dB / 40 db (WB/NB) unweighted | |
| Conducted Spurious Emission | < -80 dBm | |
| Dimensions | 29 (H) x 127 (W) x 163 (D) mm | |
| Weight | 614 grams | |
TX3820U
GENERAL
Compliance: Compliant with AS4295
Frequency Bands: UHF- 450 to 520 MHz, VHF- 136 to 174 MHz
Number of Channels: 99 + 40 UHF CB, 99 (VHF)
Channel Spacing: 25 kHz, 12.5 kHz (narrowband)
Channel Step: 6.25 kHz
Frequency Stability: +/- 1 kHz
Modulation: FM
Operation Mode: Simplex, Half Duplex
Scan Speed: 50 ms/100 ms/200 ms
Antenna Impedance: 50 Ohms
Antenna Connector: BNC
Nominal Voltage: 12V DC Negative Earth
Operating Voltage: 10.8 V to 15.6 V
Test Voltage: 13.8 V DC
Reverse Polarity: Diode Crowbar
Over Voltage Protection: 18 V Crowbar
Current: RX muted 0.2A TX 25 Watts 6A (UHF)
5A (VHF)
TRANSMITTER
RF Output: H: 25W L: 5W (adj.)
TX Duty Cycle: 1:4 for 25W Output
RF Switching BW: UHF - 70 MHz, VHF - 38 MHz
Deviation Limiting: 5 kHz / 2.5 kHz @ + 20 dB
Pre-Emphasis: +6 dB/oct + 1/-3 dB 300 Hz to 3 kHz
AF Distortion: 3% Below Limiting
Residual Modulation: -45 dB
Spurious Outputs: <-75 dBc
RECEIVER
Circuit: Double Conversion
Intermediate Frequencies: UHF 45MHz, 455 kHz, VHF 21.4 MHz,
450 kHz
Sensitivity (12 dB SINAD): -122 dBm
Adjacent Channel Selectivity: 73 dB, 65 dB (narrowband)
Intermodulation Rejection: 74 dB
Blocking: > 100 dB
Spurious Rejection: > 75 dB
RF Switching Bandwidth: UHF - 70 MHz, VHF - 38 MHz
Audio Power 3W into 4 Ohms
MECHANICAL
Dimensions: 29 (H) x 127 (L) x 163 (D) mm
Weight 620 grams
Specifications are subject to change without notice. They are issued as a guide only and shall not
form part of any contract without the express written authorisation of GME.
TX4800UV
| GENERAL | |
|---|---|
| Compliant Specification | Compliant with Australian Test Standard AS4295 |
| Frequency Bands | 148 - 174 MHz | 450 - 520 MHz |
| Number of Channels | 500 channels in 50 programmable user groups |
| Channel Spacing | 25 kHz / 12.5 kHz / 6.25 kHz |
| Frequency Stability | 2.5 ppm UHF 5 ppm VHF (-10 to +60) |
| Modulation | Direct FM |
| Operation Mode | Simplex or half duplex with repeater talk-around |
| Scanning Speed | Selectable 50/100/200 ms per channel |
| Antenna Impedance | 50 Ohms nominal |
| Antenna Connector | BNC (chassis mount) |
| Nominal Voltage | 12 volts DC negative earth |
| Operating Voltage Range | 10.8 - 15.6 volts |
| Test Voltage | 13.8 volts DC |
| Reverse Polarity Protection | Diode crowbar |
| D.C. Current | 0.3 amps receive (power save < 60 mAh) | 6 amps (UHF) transmit into 50 Ohms |
| TRANSMITTER | |
| Operating Temperature Range | -10 C to +60 C |
| RF Output | High: 25 watts max | Low: 5 watts adjustable |
| Transmit Duty Cycle | 25% at maximum output (25 watts) |
| RF Switching Bandwidth | VHF 26 MHz |
| Deviation Limiting | 2.5 kHz or 5 kHz at +20 dB AF limiting |
| Pre-Emphasis | +6 dB per Octave |
| AF Distortion | 3% below limiting |
| Residual Modulation | -40 or -45 dB |
| RECEIVER | |
| Sensitivity Spurious Outputs | -122 dB for 12 dB SINAD (CCIR) < -75 dBc (Compared to carrier) |
| Circuit Type | Double conversion superheterodyne |
| RF Switching Bandwidth | VHF-26 MHz |
| Intermediate Frequencies | 1st: 21.4 / 38.85 MHz | 2nd: 450 kHz |
| Sensitivity | -121 dBm for 12 dB SINAD unweighted |
| IF Bandwidth | 15 / 7.5 kHz WB/NB |
| Adjacent Channel Selectivity | -73 dB |
| Intermodulation | 74 dB |
| Blocking | > 100 dB |
| Spurious Rejection | > 75 dB |
| Audio Power | 4 watts average into 4 Ohms |
| Audio Signal to Noise | > 45 dB unweighted |
| Conducted Spurious Emission | < -80 dBm |
| Dimensions | 29 (H) x 127 (W) x 163 (D) mm |
| Weight | 614 grams |
TX7200
SPECIFICATIONS
General
Compliance: AS/NZS 4295
Frequency Range: 450 - 520 MHz
Number of Channels: 125
Channel Spacing: 25 kHz / 12.5 kHz
Operating Mode: Simplex or half duplex .
Scanning Speed: 40 ms per channel (25 channels
per second)
Antenna Impedance: 50 Ohms nominal
Battery Voltage: 7.2 Volts DC nominal
Operating Voltage Range: 6 - 9 Volts DC
Low Battery Alarm: 6.2 Volts DC
Reverse Voltage Protection: Shunt Diode
Operating Temperature: -10 C to +60 C
Transmitter
RF Output: High: 5 Watts
Low: 1 Watt
RF Switching Bandwidth: 70 MHz
Spurious Emission: < - 30 dBm
Frequency Stability: 5 PPM
Modulation: FM
Maximum Deviation: < 5 kHz at + 20 dB Limiting
Transmit Frequency
Response: + 6dB per octave 300 Hz to
3 kHz, + 1, - 3 dB
Audio Signal to Noise: > 45 dB.
Current Consumption (max): 1.8 Amps @ 5 Watts
0.8 Amps @ 1 Watt
Receiver
RF Switching Bandwidth: 70 MHz
Intermediate Frequencies: 1st: 21.4 MHz
2nd: 450 kHz
Sensitivity: - 122 dBm for 12 dB SINAD.
Adjacent Channel
Selectivity: 70 dB
Intermodulation: 72 dB
Blocking: 95 dB
Spurious Rejection: 65 dB
Spurious Emission: -80 dBm
Audio Output Power: 0.5 watts at <10% distortion.
Audio Signal to Noise: > 45 dB Unweighted.
Receiver Frequency
Response: - 6 dB per octave de-emphasis,
300 Hz to 3 kHz, + 1, - 3 dB.
Current Consumption: 15 mA Sleep Mode
40 mA muted
190 mA Full Volume
Mechanical Specification & Connectors
Dimensions: 135mm (W) x 63mm (D) x 40mm (H)
Weight: 390 grams
Antenna: TNC Female
All values are typical unless otherwise stated and are
subject to change without notice or obligation.
MT401
| MODES OF OPERATION | |
|---|---|
| Activated | UHF (406) and VHF (homer) complete with high intensity strobe and audible activation alert |
| Self Test | Comprehensive internal diagnostics with visual and audible operator feedback. UHF test message (inverted synchronization compatible with portable beacon testers). |
| OPERATION | |
| Activation | Manually by operator |
| Bracket Type | Manual release |
| Duration | 48 hours minimum |
| Transmission Delay | 121.5 and 406 MHz distress signals commence 60 seconds after activation |
| Warm Up | None required (due to digital frequency generation) |
| VHF | 121.5 MHz 50 mW 3 dB swept tone AM |
| UHF | 406.028 MHz* 5 W 2 dB PSK (digital) |
| Strobe | 20 flashes/minute at > 0.75 cd effective intensity |
| COPAS-SARSAT Certified to C/S T.001 (Class 2) requirements | |
| UHF-Protocol/Data | Serial user* |
| Repetition Period | 50 s mean |
| VHF | Satellite compatible phase coherent |
| BATTERY | |
| Replacement Period | Prior to expiry date marked on case |
| Replacement Method | Service centre or factory only (non-user replaceable) |
| Chemistry | LiSO2 (2.4 g Lithium per cell) |
| No./Size | 2 D size cells |
| PHYSICAL | |
| Operating | -20C to +55C |
| Storage | -30C to +70C |
| Weight | 555g (plus 98g for bracket) |
| Compass Safe | |
| Distance | 0.1m |
| Dimensions | 102 (W) x 260 (H) x 83 (D) mm max. when stowed in bracket |
| Materials | UV stabilized plastic chassis |
| Performance | IEC 61097; IEC 60945; AS/NZS 4280.1; ETSI EN 300 066 |
| OTHER FEATURES | |
| Retention Lanyard | Buoyant type approximately 5.5m long |
| Reflector | SOLAS retro-reflective tape encircling unit above waterline |
| Solid State Strobe | High reliability solid state design exceeds IMO requirements |
| Antenna | Flexible self straightening stainless steel design |
| Bracket | Quick release mechanism (manual). Retained by 4 vessel fixing points. |
| *Standard factory setting. Dealer programmable via external interface | |
| **All specifications are typical and subject to change without notice or obligation | |
MT403AUS
| MODES OF OPERATION | |
|---|---|
| Activated | UHF (406) and VHF (homer) complete with high intensity strobe and audible activation alert |
| Self Test | Comprehensive internal diagnostics with visual and audible operator feedback. UHF test message (inverted synchronization compatible with portable beacon testers). |
| OPERATION | |
| Activation | Manually by operator and automatic when deployed in water |
| Bracket Type | Manual release |
| Duration | 48 hours minimum |
| Transmission Delay | 121.5 and 406 MHz distress signals commence 60 seconds after activation |
| Warm Up | None required (due to digital frequency generation) |
| VHF | 121.5 MHz; 50 mW 3 dB; swept tone AM |
| UHF | 406.028 MHz*; 5 W 2 dB PSK (digital) |
| Strobe | 20 flashes/minute at > 0.75 cd effective intensity |
| COPAS-SARSAT Certified to C/S T.001 (Class 2) requirements | |
| UHF-Protocol/Data | Serial number*; radio call sign; MMSI |
| Repetition Period | 50 s mean |
| VHF | Satellite compatible phase coherent |
| BATTERY | |
| Replacement Period | Prior to expiry date marked on case |
| Replacement Method | Service centre or factory only (non-user replaceable) |
| Chemistry | LiMnO2 (0.49 g Lithium per cell) |
| Configuration | 5 parallel packs each of 2 series cells |
| PHYSICAL | |
| Operating | -20C to +55C |
| Storage | -30C to +70C |
| Weight | 555g (plus 98g for bracket) |
| Compass Safe Distance | 0.7m (inc. mounting bracket) from magnetic navigational device when inactive |
| Dimensions | 102 (W) x 260 (H) x 83 (D) mm max. when stowed in bracket |
| Materials | UV stabilized plastic chassis |
| Performance | IEC 61097; IEC 60945; AS/NZS 4280.1; ETSI EN 300 066 |
| Transport Class | Exempt from UN3091 |
| Patent Number | GB2420058; other patents applied for. |
| OTHER FEATURES | |
| Retention Lanyard | Buoyant type approximately 5.5m long |
| Reflector | SOLAS retro-reflective tape encircling unit above waterline |
| Solid State Strobe | High reliability solid state design exceeds IMO requirements |
| Antenna | Flexible self straightening stainless steel design |
| Bracket | Quick release mechanism (manual). Retained by 4 vessel fixing points. |
| *Standard factory setting | subject to national requirements. Distributor programmable via optical data interface. |
| **All specifications are typical and subject to change without notice or obligation | |
MT403GAUS
Specifications
| MODES OF OPERATION | |
|---|---|
| Activated | UHF (406) and VHF (homer) complete with high intensity strobe and audible activation alert |
| Self Test | Comprehensive internal diagnostics with visual and audible operator feedback. UHF test message (inverted synchronization compatible with portable beacon testers). |
| OPERATION | |
| Activation | Manually by operator and automatic when deployed in water |
| Bracket Type | Manual release |
| Duration | 48 hours minimum |
| Transmission Delay | 121.5 and 406 MHz distress signals commence 60 seconds after activation |
| Warm Up | None required (due to digital frequency generation) |
| VHF | 121.5 MHz; 50 mW 3 dB; swept tone AM |
| UHF | 406.028 MHz*; 5 W 2 dB PSK (digital) |
| Strobe | 20 flashes/minute at > 0.75 cd effective intensity |
| COPAS-SARSAT Certified to C/S T.001 (Class 2) requirements | |
| UHF-Protocol/Data | Serial number*; radio call sign; MMSI; all with GPS location |
| Repetition Period | 50 s mean |
| VHF | Satellite compatible phase coherent |
| BATTERY | |
| Replacement Period | Prior to expiry date marked on case |
| Replacement Method | Service centre or factory only (non-user replaceable) |
| Chemistry | LiMnO2 (0.49 g Lithium per cell) |
| Configuration | 5 parallel packs each of 2 series cells |
| PHYSICAL | |
| Operating | -20C to +55C |
| Storage | -30C to +70C |
| Weight | 555g (plus 98g for bracket) |
| Compass Safe Distance | 0.7m (inc. mounting bracket) from magnetic navigational device when inactive |
| Dimensions | 102 (W) x 260 (H) x 83 (D) mm max. when stowed in bracket |
| Materials | UV stabilized plastic chassis |
| Performance | IEC 61097; IEC 60945; AS/NZS 4280.1; ETSI EN 300 066 |
| Transport Class | Exempt from UN3091 |
| Patent Number | GB2420058; other patents applied for. |
| OTHER FEATURES | |
| GPS | Internal 16 channel high performance receiver with quadrifilar helix antenna |
| Retention Lanyard | Buoyant type approximately 5.5m long |
| Reflector | SOLAS retro-reflective tape encircling unit above waterline |
| Solid State Strobe | High reliability solid state design exceeds IMO requirements |
| Antenna | Flexible self straightening stainless steel design |
| Bracket | Quick release mechanism (manual). Retained by 4 vessel fixing points. |
| *Standard factory setting | subject to national requirements. Distributor programmable via optical data interface. |
| **All specifications are typical and subject to change without notice or obligation | |
MT403FF
Specifications
| MODES OF OPERATION | |
|---|---|
| Activated | UHF (406) and VHF (homer) complete with high intensity strobe and audible activation alert |
| Self Test | Comprehensive internal diagnostics with visual and audible operator feedback. UHF test message (inverted synchronization compatible with portable beacon testers). Full carrier unmodulated VHF test burst |
| OPERATION | |
| Compliance | GMDSS compatible and meets the latest IMO A810-19 requirements |
| Activation | Manually by operator and automatic when deployed in water |
| Duration | 48 hours minimum |
| Transmission Delay | 121.5 and 406 MHz distress signals commence 60 seconds after activation |
| Warm Up | None required (due to digital frequency generation) |
| VHF | 121.5 MHz; 50 mW 3 dB; swept tone AM |
| UHF | 406.028 MHz*; 5 W 2 dB; PSK (digital) |
| Strobe | 20 flashes/minute at > 0.75 cd effective intensity |
| UHF-Protocol/Data | Serial number*; radio call sign; MMSI |
| Repetition Period | 50 s mean digitally generated randomization |
| VHF | Satellite compatible phase coherent |
| BATTERY | |
| Replacement Period | Prior to expiry date marked on EPIRB case |
| Replacement Method | Authorised Service Centre |
| Chemistry | LiMnO2 (0.49 g Lithium per cell) |
| Configuration | 5 parallel packs each of 2 series cells |
| PHYSICAL | |
| Operating | -20C to +55C |
| Storage | -30C to +70C |
| EPIRB Weight | 555g (nominal) |
| Antenna | Flexible self-straightening stainless steel design |
| EPIRB Dimensions | 102 (W) x 260 (H) x 83 (D) mm |
| Materials | UV stabilized plastic chassis |
| Performance | IEC 61097; IEC 60945; AS/NZS 4280.1; ETSI EN 300 066 |
| Transport Class | Exempt from UN3091 |
| Patent Number | GB2420058; other patents applied for. |
| AUTO RELEASE HOUSING | |
| Release | Automatically before reaching 4m water depth or manually by operator |
| Protection | Impact resistant housing fully encloses EPIRB for environmental protection |
| Mounting | On flat surface fixed at 4 points to vessel - refer to instruction manual for placement |
| Housing Weight | 1.1kg (nominal) |
| Housing Dimensions | 157.5 (W) x 385.5 (H) x 102.5 (D) mm |
| Materials | Marine grade stainless steel and long life UV polypropylene stabilised enclosure |
| Routine Service | Fully user replaceable HRU at 2 year intervals as per applicable authority requirements |
| OTHER FEATURES | |
| Retention Lanyard | Buoyant type approximately 5.5m long |
| Reflector | SOLAS retro-reflective tape encircling unit above waterline |
| Solid State Strobe | High reliability solid state design exceeds IMO requirements |
| Compass Safe Distance | 0.7m (EPIRB in auto release housing) |
| *Standard factory setting | subject to national requirements. Retailer programmable via external interface. |
| **All specifications are typical and subject to change without notice or obligation | |
Clarion CZ100A
| TUNER SECTION | |
|---|---|
| Frequency bands | |
| FM: (MHz) 0.05MHz steps | 87.5 to 108 |
| AM: (kHz) 9 kHz steps | 531 to 1,629 |
| FM usable sensitivity (dBf) | 8 |
| FM 50 dB quieting sensitivity (dBf) | 17 |
| FM alternate channel selectivity (dBf) | 60 |
| FM stereo separation @1 kHz (dBf) | 30 |
| FM stereo freq. resp. @ 3 dB (Hz) | 30 to 15,000 |
| CD SECTION | |
| S/N ratio (dB) | 75 |
| Frequency response (Hz) | 20 to 20,000 |
| Dynamic range (dB) | 75 |
| Harmonic distortion (%) | 0.1 |
| AUDIO SECTION | |
| Power output (DIN45324, +B = 14.4 V) | 4 -- 22W |
| GENERAL | |
| Dimensions (W -- H -- D), mm | 178 -- 50 -- 163 |
| Remote control (W -- H -- D), mm | 44 -- 113 -- 11 |
| Weight (kg) | 1.44 |
| Power consumption: less than | 15 A |
| Speaker impedance | 4 (4 to8 allowable) |
Clarion CZ200A
| TUNER SECTION | |
|---|---|
| Frequency bands | |
| FM: (MHz) 0.05MHz steps | 87.5 to 108 |
| AM: (kHz) 9 kHz steps | 531 to 1,629 |
| FM usable sensitivity (dBf) | 8 |
| FM 50 dB quieting sensitivity (dBf) | 17 |
| FM alternate channel selectivity (dBf) | 60 |
| FM stereo separation @1 kHz (dBf) | 30 |
| FM stereo freq. resp. @ 3 dB (Hz) | 30 to 15,000 |
| CD SECTION | |
| S/N ratio (dB) | 75 |
| Frequency response (Hz) | 20 to 20,000 |
| Dynamic range (dB) | 75 |
| Harmonic distortion (%) | 0.1 |
| AUDIO SECTION | |
| Power output (DIN45324, +B = 14.4 V) | 4 -- 21W |
| GENERAL | |
| Dimensions (W -- H -- D), mm | 178 -- 50 -- 163 |
| Remote control (W -- H -- D), mm | 44 -- 113 -- 11 |
| Weight (kg) | 1.38 |
| Power consumption: less than | 15 A |
| Speaker impedance | 4 (4 to8 allowable) |
Clarion CZ500A
| TUNER SECTION | |
|---|---|
| Frequency bands | |
| FM: (MHz) 0.05MHz steps | 87.5 to 108 |
| AM: (kHz) 9 kHz steps | 531 to 1,629 |
| FM usable sensitivity (dBf) | 8 |
| FM 50 dB quieting sensitivity (dBf) | 17 |
| FM alternate channel selectivity (dBf) | 60 |
| FM stereo separation @1 kHz (dBf) | 30 |
| FM stereo freq. resp. @ 3 dB (Hz) | 30 to 15,000 |
| CD SECTION | |
| S/N ratio (dB) | 80 |
| Frequency response (Hz) | 20 to 20,000 |
| Dynamic range (dB) | 80 |
| Harmonic distortion (%) | 0.1 |
| AUDIO SECTION | |
| Power output (DIN45324, +B = 14.4 V) | 4 -- 25W |
| GENERAL | |
| Dimensions (W -- H -- D), mm | 178 -- 50 -- 163 |
| Remote control (W -- H -- D), mm | 44 -- 113 -- 11 |
| Weight (kg) | 1.30 |
| Power consumption: less than | 15 A |
| Speaker impedance | 4 (4 to8 allowable) |
GME TX3100
| GENERAL | |
|---|---|
| Compliant Specification | AS/NZS 4365 |
| Frequency Range | 425-477.4 MHz |
| Number of Channels | 40 UHF CB |
| Channel Spacing | 25 kHz |
| Operation Mode | Simplex channels 1-40 |
| Scanning Speed | 20 channels per second |
| Antenna Impedance | 50 Ohms nominal |
| Operating Voltage Range | 10-15 Volts DC |
| Nominal Battery Voltage | 13.8 Volts DC |
| Over Voltage Protection | 25 Volts DC max. At 18 Volts DC the RF power is reduced |
| Over Current Protection | In-line 2A Fuse |
| Reverse Polarity Protection | Shunt Diode |
| Freq uency Stability | 5 PPM |
| TRANSMITTER | |
| RF Output | 5.0 Watts max. |
| Modulation | FM |
| Maximum Deviation | < 5 kHz at + 20 dB limiting |
| Spurious Emissions | < - 70 dBc |
| Transmit Frequency Response | + 6 dB per octave 300 Hz to 3 kHz + 1-3 dB. |
| Audio Signal to Noise | > 45 dB |
| Current Consumption | 1.5 Amps with 50 Ohm termination |
| RECEIVER | |
| Circuit Type | Double Conversion Superheterodyne |
| Intermediate Frequencies | 1st - 21.4 MHz 2nd - 450 kHz |
| Current Consumption | < 180 mA muted 600 mA @ max. A.F output |
| Sensitivity | - 123 dBm for 12 dB SINAD unweighted |
| Selectivity | - 6 dB at + 7.5 kHz ' 70 dB at 25 kHz |
| Intermodulation Immunity | 73 dB |
| Blocking Immunity | 100 dB |
| Spurious Response Immunity | 70 dB |
| Audio Power | 3 Watts average into 4 Ohms |
| Audio Signal to Noise | > 45 dB |
| Receive Frequency Response | ' 6 dB/Octave de'emphasis 300 Hz to 3 kHz + 1-3 dB |
| Conducted Spurious Emission | < - 57 dBm |
| MECHANICAL | |
| Dimensions | 102 (W) x 87 (D) x 23 (H) mm |
| Weight | 158 grams |
| Shock and Vibration | MIL STD 810 method |
| ENVIRONMENTAL | |
| Temperature Range | -10C to +60C |
GME TX3340
| GENERAL | |
|---|---|
| Compliant Specification | AS/NZS 4365 |
| Frequency Range | 476.425-477.4 MHz |
| Number of Channels | 40 UHF CB |
| Channel Spacing | 25 kHz |
| Operation Mode | Simplex channels 1-40 |
| Scanning Speed | 20 channels per second |
| Antenna Impedance | 50 Ohms nominal |
| Operating Voltage Range | 10-15 Volts DC |
| Nominal Battery Voltage | 13.8 Volts DC |
| Over Voltage Protection | 25 Volts DC max. At 18 Volts DC the RF power is reduced |
| Over Current Protection | In-line 2A Fuse |
| Reverse Polarity Protection | Shunt Diode |
| Frequency Stability | 5 PPM |
| Selcall Tone Length | 40 ms |
| TRANSMITTER | |
| RF Output | 5.0 Watts max. |
| Modulation | FM |
| Maximum Deviation | < 5 kHz at + 20 dB limiting |
| Spurious Emissions | < - 70 dBc |
| Transmit Frequency Response | + 6 dB per octave 300 Hz to 3 kHz + 1-3 dB. |
| Audio Signal to Noise | > 45 dB |
| Current Consumption | 1.5 Amps with 50 Ohms termination |
| RECEIVER | |
| Circuit Type | Double Conversion Superheterodyne |
| Intermediate Frequencies | 1st - 21.4 MHz 2nd - 450 kHz |
| Current Consumption | < 180 mA muted 600 mA @ max. A.F output |
| Sensitivity | - 123 dBm for 12 dB SINAD unweighted |
| Selectivity | - 6 dB at + 7.5 kHz ' 70 dB at 25 kHz |
| Intermodulation Immunity | 73 dB |
| Blocking Immunity | 100 dB |
| Spurious Response Immunity | 70 dB |
| Audio Power | 3 Watts average into 4 Ohms |
| Audio Signal to Noise | > 45 dB |
| Receive Frequency Response | ' 6 dB/Octave de'emphasis 300 Hz to 3 kHz + 1-3 dB |
| Conducted Spurious Emission | < - 57 dBm |
| MECHANICAL | |
| Dimensions | 102 (W) x 87 (D) x 23 (H) mm |
| Weight | 158 grams |
| Shock and Vibration | MIL STD 810 method |
| ENVIRONMENTAL | |
| Temperature Range | -10C to +60C |
GR200 - AM/FM/VHF Broadcast Radio
| |||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
GD9620 - Marine DVD/CD/MP3 Player
| FM RADIO | |
|---|---|
| Frequency Range | 87.5 - 108 MHz (Eu./Aust./N.Z.) 87.5 - 107.9 MHz (U.S.A.) |
| Frequency Step | 50 kHz |
| Intermediate Frequency | 10.7 MHz |
| Sensitivity (30 dB S/N) | 13 dBuV (typical) |
| Channel Separation | 22 dB |
| Station Memories | 18 |
| AM RADIO | |
| Frequency Range | 522 - 1620 MHz (Eu./Aust./N.Z.) 530 - 1710 MHz (U.S.A.) |
| Frequency Step | 9 kHz (Eu./Aust./N.Z.) 10 kHz (U.S.A.) |
| Intermediate Frequency | 455 kHz |
| Sensitivity (20 dB S/N) | 25 dBuV |
| Station Memories | 12 |
| COMPACT DISK MECHANISM | |
| Mechanism | Auto Loading |
| Signal to Noise Ratio | 65 dB |
| Format | 8 times oversampling |
| Environmental | Anti-vibration/Anti-shock |
| AUDIO AMPLIFIER | |
| Audio Output | (4 channels x 45 W Peak = 180 W Peak) @ 10% THD. |
| Speaker Impedance | 4 Ohms |
| Frequency Response | 40 Hz - 18 kHz |
| Bass Adjustment Range | ++/- 8 dB @ 100 kHz |
| Treble Adjustment Range | ++/- 10 dB @ 10 kHz |
| DVD PLAYER | |
| Aspect Ratio | 4:3 Letter box 4:3 Pan Scan or 16:9 |
| Video Output Level | 1.00 volt Peak to Peak (75 Ohms Impedance) |
| Horizontal Resolution | 500 |
| Video System | Auto/PAL/NTSC |
| GENERAL | |
| DC Supply Input | 11 - 16 volts Negative Ground |
| Memory Back-up | External Back-up Memory Wire |
| Back-up Current | Approximately 20 mA |
| Overall Size | 232 mm (W) x 97 mm (H) x 200 mm (D) excluding heat dissipator. |
| Weight | 1.75 kg |
| Supply Current | 7 Amps (max.) |
GD9640 - DVD/CD/MP3 Player - Bracket Mount
| FM RADIO | |
|---|---|
| Frequency Range | 87.5 - 108 MHz (Eu./Aust./N.Z.) 87.5 - 107.9 MHz (U.S.A.) |
| Frequency Step | 50 kHz |
| Intermediate Frequency | 10.7 MHz |
| Sensitivity (30 dB S/N) | 13 dBuV (typical) |
| Channel Separation | 22 dB |
| Station Memories | 18 |
| AM RADIO | |
| Frequency Range | 522 - 1620 MHz (Eu./Aust./N.Z.) 530 - 1710 MHz (U.S.A.) |
| Frequency Step | 9 kHz (Eu./Aust./N.Z.) 10 kHz (U.S.A.) |
| Intermediate Frequency | 455 kHz |
| Sensitivity (20 dB S/N) | 25 dBuV |
| Station Memories | 12 |
| COMPACT DISK MECHANISM | |
| Mechanism | Auto Loading |
| Signal to Noise Ratio | 65 dB |
| Format | 8 times oversampling |
| Environmental | Anti-vibration/Anti-shock |
| AUDIO AMPLIFIER | |
| Audio Output | (4 channels x 45 W Peak = 180 W Peak) @ 10% THD. |
| Speaker Impedance | 4 Ohms |
| Frequency Response | 40 Hz - 18 kHz |
| Bass Adjustment Range | ++/- 8 dB @ 100 kHz |
| Treble Adjustment Range | ++/- 10 dB @ 10 kHz |
| DVD PLAYER | |
| Aspect Ratio | 4:3 Letter box 4:3 Pan Scan or 16:9 |
| Video Output Level | 1.00 volt Peak to Peak (75 Ohms Impedance) |
| Horizontal Resolution | 500 |
| Video System | Auto/PAL/NTSC |
| GENERAL | |
| DC Supply Input | 11 - 16 volts Negative Ground |
| Memory Back-up | External Back-up Memory Wire |
| Back-up Current | Approximately 20 mA |
| Overall Size | 232 mm (W) x 97 mm (H) x 200 mm (D) excluding heat dissipator. |
| Weight | 1.75 kg |
| Supply Current | 7 Amps (max.) |
GME GX600
| GENERAL | |
|---|---|
| Compliance | AS/NZS4415.2.2003 |
| Frequency Range | 155 - 165 MHz |
| Channel Spacing | 25 kHz |
| Modulation | FM |
| Channel Sets | International/USA/Canada |
| Private - 10 channels | |
| USA weather channels | |
| Customer weather channels | |
| Supply Voltage | 12 Volt nominal |
| 10.5 - 15.6 Volt max. range | |
| Negative Earth | |
| Frequency Stability | 1.5 kHz over environment extremes |
| Scan Speed | 100 ms/channel (10 channels/sec) |
| TRANSMITTER | |
| Power Output | High: 25 Watts max. |
| Low: 1 Watt max. | |
| Spurious Emissions | <-75 dBc |
| Frequency Deviation | 5 kHz max. + 20 dB limiting @1 kHz |
| Frequency Response | + 6 dB per octave; 300 Hz - 3 kHz; +1 - 3 dB |
| Demodulated S/N | >50 dB weighted |
| Current Consumption | High power: <5 Amps |
| Low power: 850 mA | |
| RECEIVER | |
| IF Frequencies | 1st: 21.4 MHz |
| 2nd: 450 kHz | |
| Sensitivity | -121 dBm for 12 dB SINAD unweighted |
| Spurious Rejection | >70 dB |
| Intermodulation Rejection | >75 dB |
| Adjacent Channel Rejection | >74 dB |
| Blocking Rejection | >100 dB |
| RF Bandwidth | <4 MHz |
| Switching Bandwidth | >10 MHz |
| Frequency Response | -6 dB per octave de-emphasis; 300 Hz - 3 kHz; +1 - 3 dB |
| Audio Output Power | 4 Watts average into external 4 Ohm speaker |
| 2 Watts average into internal speaker | |
| Audio SN | >50 dB weighted |
| Conducted Spurious Emission | <-70 dBm |
| Current Consumption | Muted <200 mA |
| Full volume: 700 mA | |
| MECHANICAL | |
| Dimensions | 164 (W) x 65 (H) x 77 (D) mm |
| Flush Mounting Depth | 45 mm min. |
| Weight | 585 g |
| ENVIRONMENTAL | |
| Temperature Range | -10C to +55C |
| Vibration | MIL STD 810E; procedure I 3.4.8 |
| Solar Radiation | Case UV stabilised |
| Water and Dust Resistance | IP67 excluding external cabling |
| Compass Safe Distance | 300 mm |
| EXTERNAL CONNECTIONS | |
| Microphone | 6 Pin socket |
| DC Supply | 2 Pin blade socket |
| External Speaker | 3.5 mm phono line socket |
| *All specifications are typical and subject to change without notice or obligation | |
GME TX4500
| Electrical | |
|---|---|
| General | |
| Compliant Specification | Meets AS/NZS 4365 for radio communications equipment in the UHF citizen and personal radio service. |
| Frequency Range TX | 476.425-477.4125 MHz |
| Number of Channels | 80 |
| Channel Spacing | 12.5 kHz |
| Operation Mode | Simplex or half Duplex with repeater talk around. |
| Scanning Speed | 50 ms per channel (20 channels per second). |
| Antenna Impedance | 50 Ohms nominal |
| Nominal Battery Voltage | 12 volts DC |
| Operating Voltage Range | 10-16 volts DC |
| Battery Polarity | Negative Earth |
| Standard Test Voltage | 13.8 volts DC |
| Overvoltage Protection | 25 volts DC maximum. At 18 volts DC the channel display flashes 'Hi DC' for 5 seconds on receive. The RF power is reduced and TX flashes on transmit. |
| Reverse Voltage Protection: Diode Crowbar | |
| Overcurrent Protection | In-line 2 amp fuse |
| Operating Temperature | -10C to 60C |
| Transmitter | |
| RF Output | 5 watts |
| Spurious Emission | < - 70 dBc |
| Frequency Error | < 1.5 kHz |
| Modulation | FM |
| Maximum Deviation | < 2.5 kHz at + 20 dB AF limiting. |
| Transmit Frequency Response | + 6 dB per octave 300 Hz to 3 kHz + 1-3 dB. |
| Demodulated Audio Signal to Noise | > 45 dB unweighted |
| Current Consumption | 1.7 amps with 50 Ohms termination. |
| Receiver | |
| Intermediate Frequencies | 38.85 MHz |
| Sensitivity | - 122 dBm for 12 dB SINAD unweighted |
| Selectivity | - 6 dB at + 3.5 kHz ' 60 dB at 12.5 kHz |
| Intermodulation Immunity | -72 dB |
| Blocking Immunity | -98 dB |
| Spurious Response Immunity | 70 dB |
| Audio Output Power | 3 watts average into 4 Ohms |
| Audio Signal to Noise | > 45 dB unweighted |
| Receive Frequency | |
| Response | 6 dB/Octave de'emphasis 300 Hz to 3 kHz + 1-3 dB. |
| Current Consumption | < 175 mA muted 750 mA Full volume. |
| Conducted Spurious Emission | < - 70 dBm |
| Mechanical Specifications & Connections | |
| Dimensions | 50 (H) x 171 (L) x 112 (D) mm |
| Weight | 646 grams |
| 12 volt Power Supply | Two core cable with bulkhead connector in rear panel. |
| Antenna | SO239 Panel Socket |
| External Speaker | 3.5 mm Mono Jack |
| Microphone Port | 6 Way telephone style with rubber strain relief. |
GME TX655
Specifications
| GENERAL | |
|---|---|
| Complies with | AS/NZS 4365:2011 for radio communications equipment in the UHF CB and personal radio service. |
| Frequency Range | 476.425 - 477.4125 MHz |
| Number of Channels | 80 (75 Voice - 2 Telemetry-RX only - 3 Guard-RX only) |
| Channel Spacing | 12.5 kHz |
| Operating Mode | Simplex or half duplex |
| Privacy Codes | 38 |
| Operating Temperature | -10C to + 60C |
| Battery Source | Li-Ion 3.7 V DC 720 mAh rechargeable battery pack |
| Operating Time | 10 Hrs (Transmit 5% - Receive 5% - Standby 90%) |
| TRANSMITTER | |
| RF Output | Hi - 1 watt / Low - 0.5 watts |
| Modulation | FM |
| Max. Deviation | 2.5 kHz |
| Modulation Distortion | < 5% (1 kHz 70%) |
| RECEIVER | |
| Usable Sensitivity | > - 118 dBm |
| Maximum Audio Output | > 0.3 watts maximum (8 Ohms) |
| Modulation Distortion | |
MT410 PLB
| MODES OF OPERATION | |
|---|---|
| Activated | UHF (406) and VHF (homer) complete with high intensity light and audible alert |
| Self Test | Comprehensive internal diagnostics with visual and audible operator feedback. UHF test message (inverted synchronization compatible with portable beacon testers). |
| OPERATION | |
| Activation | Automatically when antenna deployed |
| Duration | In excess if 24 hours at -20C; longer at higher ambient temperatures |
| Transmission | 121.5 and 406 MHz |
| Delay | 60 seconds to deactivate prior to distress transmission |
| Warm Up | None required (due to patented digital frequency generation) |
| VHF | 121.5 MHz; 50 mW 3 dB; swept tone AM (analogue) |
| UHF | 406.028 MHz; 5 W 2 dB; PSK (digital) |
| Light | > 20 flashes/minute at; 2 x high intensity white LED |
| COPAS-SARSAT | |
| Certified to C/S T.001 (Class 2) requirements | |
| UHF-Protocol/Data | Supports all short operation protocols (re-programmable by Distributor) |
| Repetition Period | 50 s mean |
| VHF | Satellite compatible phase coherent |
| BATTERY | |
| Replacement Period | Prior to expiry date marked on case - (7 yrs) or after use |
| Replacement Method | Service centre or factory only (non-user replaceable) |
| Chemistry | LiMnO2 (2.4 g Lithium per cell) |
| Configuration | 2 electronically isolated batteries consisting of 2 cells type CR17345 |
| PHYSICAL | |
| Operating | -20C to +55C |
| Storage | -30C to +70C |
| Weight | 235g |
| Compass Safe Distance | 0.1m (for minimal deflection) |
| Dimensions | 71 (W) x 135 (H) x 38 (D) mm |
| Buoyant | Will float in fresh/salt water (RTM Cat 1) |
| Waterproof | Submersion to 1m exceeds IP67 |
| Materials | High visibility yellow chassis with translucent cap. UV stabilised high impact plastic chassis with energy absorption over-moulded bumpers. |
| OTHER FEATURES | |
| Standards and Approvals | AS/NZS 4280.2; ETSI EN 302 152-1 (CE0168!); RTCM 76-2002/SC110; FCC ID: TXJMT410-G |
| Transport | Meets UN requirements for transport as non-hazardous cargo on board passenger aircraft |
| Antenna | Flexible self-straightening and robust wire rope design. Marine grade 316 Stainless Steel. |
| *All specifications are typical and subject to change without notice or obligation | |
MT410GAUS PLB
| MODES OF OPERATION | |
|---|---|
| Activated | UHF (406) and VHF (homer) complete with high intensity light and audible alert |
| Self Test | Comprehensive internal diagnostics with visual and audible operator feedback. UHF test message (inverted synchronization compatible with portable beacon testers). GPS satellite acquisition test. |
| OPERATION | |
| Activation | Automatically when antenna deployed |
| Duration | In excess if 24 hours at -20C; longer at higher ambient temperatures |
| Transmission | 121.5 and 406 MHz |
| Delay | 60 seconds to deactivate prior to distress transmission |
| Warm Up | None required (due to patented digital frequency generation) |
| VHF | 121.5 MHz; 50 mW 3 dB; swept tone AM (analogue) |
| UHF | 406.028 MHz; 5 W 2 dB; PSK (digital) |
| Light | > 20 flashes/minute at; 2 x high intensity white LED |
| COPAS-SARSAT | |
| Certified to C/S T.001 (Class 2) requirements | |
| UHF-Protocol/Data | Supports all short and long operation protocols (re-programmable by Distributor) |
| Repetition Period | 50 s mean |
| VHF | Satellite compatible phase coherent |
| BATTERY | |
| Replacement Period | Prior to expiry date marked on case - (7 yrs) or after use |
| Replacement Method | Service centre or factory only (non-user replaceable) |
| Chemistry | LiMnO2 (2.4 g Lithium per cell) |
| Configuration | 2 electronically isolated batteries consisting of 2 cells type CR17345 |
| PHYSICAL | |
| Operating | -20C to +55C |
| Storage | -30C to +70C |
| Weight | 250g |
| Compass Safe Distance | 0.1m (for minimal deflection) |
| Dimensions | 71 (W) x 135 (H) x 38 (D) mm |
| Buoyant | Will float in fresh/salt water (RTM Cat 1) |
| Waterproof | Submersion to 1m exceeds IP67 |
| Materials | High visibility yellow chassis with translucent cap. UV stabilised high impact plastic chassis with energy absorption over-moulded bumpers. |
| GPS RECEIVER | |
| Type | Ultra high sensitivity L1 frequency C/A |
| 50 search channel 8192 time/frequency search windows | |
| Antenna | Dielectrically loaded quadrifilar helix |
| Acquisition | Cold start 34 seconds typically; hot start <3.5 seconds typical |
| Position | Located to within 45m typical |
| OTHER FEATURES | |
| Standards and Approvals | AS/NZS 4280.2; ETSI EN 302 152-1 (CE0168!); RTCM 76-2002/SC110; FCC ID: TXJMT410-G |
| Transport | Meets UN requirements for transport as non-hazardous cargo on board passenger aircraft |
| Antenna | Flexible self-straightening and robust wire rope design. Marine grade 316 Stainless Steel. |
| *All specifications are typical and subject to change without notice or obligation | |
XR-150 spec
GENERAL
Compliance:CE , FCC , AS/NZS 4295 : 2004
Dimension:103mm (H) X 52mm (W) X 32mm (D)
Weight:250g with 2200 mAH Battery
Frequency range:136 MHz to 174 MHz
Channels:512 Channels in 16 Groups
Nominal Voltage:7.5 Volts DC
Channel Spacing:12.5 and 25 KHz programmable per channel
Coverage:Up to 6 miles (in open space)
RECEIVER
Sensitivity: 0.25V for 12 dB SINAD
Selectivity: Better than 70dB @25KHz ; 65db@12.5KHz
Supurious Response: 70 dB
Audio Output: 1 watt @ 16 Ohms
Channel Spread: 34 MHz without tuning
Battery Drain: Stand by 45mA
TRANSMITTER
RF Power output: 4 watts (High) & 2 watts (low)
Hum & Noise: 45dB @ 25KHz & 40 dB @ 12.5KHz
Modulation Distortion: 3% max. @ 1000Hz
Channel Spead: 34 MHz without tuning
Nominal Battery Drain: 1.7 Amps @ 5 watts
ENVIRONMENTALS
Operating Temperature: -30 C to +60 C
Storage Temperature: -55 C to +85 C
Humidity: 95% RH @ 8 hrs
ESD: IEC 801-2 KV
Water Intrusion IP-54
XR-450 spec
GENERAL
Compliance: CE , FCC , AS/NZS 4295 : 2004
Dimension: 103mm (H) X 52mm (W) X 32mm (D)
Weight: 250g with 2200 mAH Battery
Frequency range: 450 MHz to 512 MHz
Channels: 512 Channels in 16 Groups
Nominal Voltage: 7.5 Volts DC
Channel Spacing: 12.5 and 25 KHz programmable per channel
Coverage: Up to 5 miles (in open space)
RECEIVER
Sensitivity: 0.25V for 12 dB SINAD
Selectivity: Better than 70dB @25KHz ; 65db@12.5KHz
Supurious Response: 70 dB
Audio Output: 1 watt @ 16 Ohms
Channel Spread: 70 MHz without tuning
Battery Drain Stand by: 45mA
TRANSMITTER
RF Power output: 4 watts (High) & 2 watts (low)
Hum & Noise: 45dB @ 25KHz & 40 dB @ 12.5KHz
Modulation Distortion: 3% max. @ 1000Hz
Channel Spead: 70 MHz without tuning
Nominal Battery Drain: 1.7 Amps @ 5 watts
ENVIRONMENTALS
Operating Temperature: -30 C to +60 C
Storage Temperature: -55 C to +85 C
Humidity: 95% RH @ 8 hrs
ESD: IEC 801-2 KV
Water Intrusion IP-54
XR-450M spec
GENERAL
Compliance: CE , FCC , AS/NZS 4295 : 2004
Dimension: 103mm (H) X 52mm (W) X 32mm (D)
Weight: 250g with 2200 mAH Battery
Frequency range: 450 MHz to 512 MHz
Channels: 512 Channels in 16 Groups
Nominal Voltage: 7.5 Volts DC
Channel Spacing: 12.5 and 25 KHz programmable per channel
Coverage: Up to 5 miles (in open space)
RECEIVER
Sensitivity: 0.25V for 12 dB SINAD
Selectivity: Better than 70dB @25KHz ; 65db@12.5KHz
Supurious Response: 70 dB
Audio Output: 1 watt @ 16 Ohms
Channel Spread: 70 MHz without tuning
Battery Drain Stand by: 45mA
TRANSMITTER
RF Power output: 4 watts (High) & 2 watts (low)
Hum & Noise: 45dB @ 25KHz & 40 dB @ 12.5KHz
Modulation Distortion: 3% max. @ 1000Hz
Channel Spead: 70 MHz without tuning
Nominal Battery Drain: 1.7 Amps @ 4 watts
ENVIRONMENTALS
Operating Temperature: -30 C to +60 C
Storage Temperature: -55 C to +85 C
Humidity: 95% RH @ 8 hrs
ESD: IEC 801-2 KV
Water Intrusion IP-68
GME TX3520W Specs
| General | |
|---|---|
| Compliant Specification | Meets AS/NZS 4365 for radio communications equipment in the UHF citizen and personal radio service. |
| Frequency Range TX | 476.425-477.4125 MHz |
| Number of Channels | 80 |
| Channel Spacing | 12.5 kHz |
| Operation Mode | Simplex or half Duplex with repeater talk around. |
| Scanning Speed | 50 ms per channel (20 channels per second). |
| Antenna Impedance | 50 Ohms nominal |
| Nominal Battery Voltage | 12 V DC |
| Operating Voltage Range | 10-16 V DC |
| Battery Polarity | Negative Earth |
| Standard Test Voltage | 13.8 V DC |
| Overvoltage Protection | 30 V DC maximum. At 18 volts DC the channel display flashes 'Hi DC' for 5 seconds on receive. The RF power is reduced and TX flashes on transmit. |
| Reverse Voltage Protection | Diode Crowbar |
| Overcurrent Protection | In-line 2 amp fuse |
| Operating Temperature | -10C to 60C |
| Transmitter | |
| RF Output | 5 watts |
| Spurious Emission | < - 70 dBc |
| Frequency Error | < 1.5 kHz |
| Modulation | FM |
| Maximum Deviation | < 2.5 kHz at + 20 dB AF limiting. |
| Transmit Frequency Response | + 6 dB per octave 300 Hz to 3 kHz + 1-3 dB. |
| Demodulated Audio Signal to Noise | > 45 dB unweighted |
| Current Consumption | 1.7 amps with 50 Ohms termination. |
| Receiver | |
| Intermediate Frequencies | 38.85 MHz |
| Sensitivity | - 122 dBm for 12 dB SINAD unweighted |
| Selectivity | - 6 dB at + 3.5 kHz ' 60 dB at 12.5 kHz |
| Intermodulation Immunity | -72 dB |
| Blocking Immunity | -98 dB |
| Spurious Response Immunity | 70 dB |
| Audio Output Power | 3 watts average into 4 Ohms |
| Audio Signal to Noise | > 45 dB unweighted |
| Receive Frequency Response | ' 6 dB/Octave de'emphasis 300 Hz to 3 kHz + 1-3 dB. |
| Current Consumption | < 175 mA muted 750 mA Full volume. |
| Conducted Spurious Emission | < - 70 dBm |
| Mechanical Specifications & Connections | |
| Dimensions | 29 (H) x 128 (L) x 117 (D) mm |
| Weight | 450 grams |
| 12 Volt Power Supply | Two core cable with bulkhead connector in rear panel. |
| Antenna | SO239 Panel Socket |
| External Speaker | 3.5 mm Mono Jack |
| Microphone Port | 6 Way telephone style with rubber strain relief. |
GP450X Specs
Channels: 12 parallel channels
WASS/EGNOS/MSAS: 1 additional channel
Waypoints: 999
Routes: 50 routes with 30 Waypoints per route
Tracks: 2500 points
Max. Velocity: 500 m/s (972 knots)
Accuracy: <15m (95%)
Acceleration: 4g
Altitude: 18000 m
Acquisition time: Hot - 15 secs Warm: 45 secs
LCD type: Monochrome
LCD dimensions: 95 (w) x 63 (h) mm
LCD resolution: 240 (w) x 160 (h) pixels
Alarms: Arrival Anchor
GME TX6500
Specifications
| GENERAL | |
|---|---|
| Compliance | Compliant with AS/NZS 4365 for radio communications equipment in the UHF citizen band and personal radio service. |
| Frequency Range | 476.425 MHz - 477.4125 MHz |
| Number of Channels | 80 (plus 95 receive only) |
| Tuneable Frequency Range (receive only) | 403 MHz - 520 MHz |
| Channel Spacing | 12.5 kHz |
| Operating Mode | Simplex or half duplex |
| Scanning Speed | 40 ms per channel (25 channels per second) |
| Antenna Impedance | 50 Ohms nominal |
| Battery Voltage | 7.4 volts DC nominal |
| Operating Voltage Range | 6 - 9 volts DC |
| Low Battery Alarm | 6.9 volts DC |
| Reverse Voltage Protection | Shunt Diode |
| Operating Temperature | -20 C to +60 C |
| Frequency Stability | 2.5 PPM |
| Modulation | FM |
| TRANSMITTER | |
| RF Output | High: 5 watts Low: 1 watt |
| Conducted Spurious Emission | < -75 dBm |
| Maximum Deviation | < 2.5 kHz at + 20 dB limiting |
| Transmit Frequency Response | +6 dB per octave 300 Hz to 3 kHz |
| Current Consumption (max) | 2.0 amps typical |
| RECEIVER | |
| Sensitivity (450 - 520 MHz) | -121 dBm for 12 dB SINAD |
| Intermediate Frequencies | 1st: 38.85 MHz 2nd: 450 kHz |
| Adjacent Channel Selectivity | >65 dB |
| Intermodulation Immunity | >65 dB |
| Blocking Immunity | >90 dB |
| Spurious Response Immunity | >70 dB |
| Image Rejection | >60 dB |
| Audio Output Power | 1 watt at <10% distortion |
| Audio Signal to Noise | > 40 dB |
| Receiver Frequency Response | 6 dB per octave de-emphasis 300 Hz to 3 kHz + 1 -3 dB |
| Squelch | SQL-1: -122 dBm typical SQL-9: -110 dBm typical |
| Current Consumption | 40 mA sleep mode 80 mA muted 340 mA full volume |
| MECHANICAL | |
| Dimensions | 60 mm (W) x 40 mm (D) x 130 mm (H) (not including antenna) |
| Weight | 340 grams |
| Antenna | TNC female |
| Speaker/Microphone/Programming | 8 pin connector |
| Battery Rapid Charging | 4 plated terminals with temperature sensor |
| NOTE: All values are typical unless otherwise stated and are subject to change without notice | |
| or obligation. | |
UBDA220 #AU Specifications
|
|||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
RNG-AMP
Part Number RNG-AMP RIS-AMP
Physical
Construction Single Printed Circuit Board
Enclosure NEMA 4x (IP66),
Polycarbonate
NEMA 4x (IP66) Fiberglass
reinforced polyester plastic
Dimensions (L x H x W) 323 x 90 x 180 mm
(12.7 x 3.5 x 7.1 in)
323 x 121 x 250 mm
(12.7 x 4.8 x 9.8 in)
Weight (nominal) 1.00 kg (2.20 lbs) 3.20 kg (7.05 lbs)
Connectors Two 3 Terminal Lug Connectors, PG21 cable grips
Two test BNC jack ports
Conformal Coating No 2 coats, CTI > 100
Environmental
Temperature Range -20 to +60 C (-4 to +140 F)
Electrical
Input Voltage 5.5 - 36 Vdc 5.5 -12.5 Vdc
Current Consumption 128 mA @ 12 Vdc
73 mA @ 36 Vdc
128 mA @ 12 Vdc
DC Blocking Jumper Selection on Board Input/Output
RF Characteristics
Input Impedance 75 ohms
Leaky Cable Types Varis RNG-500, Varis RNG-501
Downstream
Gain 10-25 dB
Gain Adjust Range 15 dB (MGC and AGC)
Gain Control MGC, AGC (No Upstream Pilot required)
Bandwidth (3 dB) 15 MHz
3 dB Bandpass 145-160 MHz
3rd Order Intermod free
Channel Capacity
16 Voice/Data, 8 Video (2 per main branch)
Ethernet Bandpass 6.0 MHz
Becker - U3SP100WW##AU
|
|||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Becker - UEOL100WW#
Specifications
| Description | Specifics |
|---|---|
| Frequency Band | 100 - 500Mhz |
| Connectors | 1 Brass Block connector |
| VSWR | 1.4:1 (150MHz to 175MHz) |
| Power Requirement | None - Passive |
GME TDR1000
Specifications
| Input voltage range | 6 V DC to 32 V DC |
| DC input power | 150 watt input |
| Supplied AC adaptor | Input = 90 to 264 V AC input 47-63 Hz |
| Output = 13 V DC at 14 A constant current capable | |
| Battery | 2 x nominal 12 V SLA or LiFePO4 |
| 7-9 A hrs capacity each | |
| Recharge time | 3 hrs minimum with supplied AC adaptor |
| Longer with low capacity source | |
| Radio voltage | 12 V DC regulated |
| Multi Function Status Display | |
|---|---|
| Displays | Battery isolator |
| Power On/Off speaker microphone volume control | |
| Volume | |
| Link channel change on mic | |
| Battery capacity fuel gauge | |
| Bar graph - 0-100% | |
| Battery charging | |
| DC Input voltmeter | |
| On/Off - Receiver-link Busy-speaker on | |
| Operating temperature | Depending on battery choice |
| -15C to 65C | |
| Protection | Input = reverse |
| High internal temperature | |
| Flexible external power sources | Supports wide range of input voltage and current |
| eg 12 V DC and 24 V DC vehicle supplies | |
| Mechanical | |
| TDR1000 (dimensions) | 50 (w) x 40 (d) x 20 (h) cm |
| Weight with radio compliment | 12.5 kg |
| AE1000 (dimensions) | 25 (w) x 125 (h) cm |
| Total weight | < 20 kg |
| Specifications are subject to change without notice. They are issued as a guide only and shall not form part of any contract without the express written authorisation of GME. | |
| *Refer to www.gme.net.au for IP67 rating. | |